Universalgreifer Schunk Parallelgreifer PGN 125/1 (370103) for industrial equipment
Buchen
If you decide to buy equipment at a low price, make sure that you communicate with the real seller. Find out as much information about the owner of the equipment as possible. One way of cheating is to represent yourself as a real company. In case of suspicion, inform us about this for additional control, through the feedback form.
Before you decide to make a purchase, carefully review several sales offers to understand the average cost of your chosen equipment. If the price of the offer you like is much lower than similar offers, think about it. A significant price difference may indicate hidden defects or an attempt by the seller to commit fraudulent acts.
Do not buy products which price is too different from the average price for similar equipment.
Do not give consent to dubious pledges and prepaid goods. In case of doubt, do not be afraid to clarify details, ask for additional photographs and documents for equipment, check the authenticity of documents, ask questions.
The most common type of fraud. Unfair sellers may request a certain amount of advance payment to “book” your right to purchase equipment. Thus, fraudsters can collect a large amount and disappear, no longer get in touch.
- Transfer of prepayment to the card
- Do not make an advance payment without paperwork confirming the process of transferring money, if during the communication the seller is in doubt.
- Transfer to the “Trustee” account
- Such a request should be alarming, most likely you are communicating with a fraudster.
- Transfer to a company account with a similar name
- Be careful, fraudsters may disguise themselves as well-known companies, making minor changes to the name. Do not transfer funds if the company name is in doubt.
- Substitution of own details in the invoice of a real company
- Before making a transfer, make sure that the specified details are correct, and whether they relate to the specified company.
Seller's contacts
Germany 
Germany, Buchen
Germany, Buchen
Germany, Buchen
Germany, Buchen
Germany, Buchen
Germany, Buchen
Germany, Buchen
Germany, Buchen
Germany, Buchen
Germany, Wiefelstede
Germany, Buchen
Germany, Freiberg am Neckar
Germany, Buchen
Germany, Buchen
Germany, Buchen
Germany, Enger
Germany, Buchen
Germany, Buchen
Germany, Buchen
Germany, Buchen
Schunk Universal Gripper PGN-plus 380-1 AS
Stroke per jaw [mm]
Closing force [N]
Closing force (at finger length 0 mm) [N]
Minimum spring force [N]
Net weight [kg]
Recommended workpiece weight [kg]
Cylinder volume per double stroke [cm³]
Minimum operating pressure [bar]
Max. operating pressure [bar]
Nominal operating pressure [bar]
Minimum sealing air pressure [bar]
Max. sealing air pressure [bar]
Closing time [s]
Opening time [s]
Closing/opening time with spring [s]
Maximum permissible finger length [mm]
Maximum permissible mass per finger [kg]
Protection class IP
Minimum ambient temperature [°C]
Max. ambient temperature [°C]
Repeatability [mm]
Length X [mm]
Width Y [mm]
Height Z [mm]
Maximum torque [Nm]
Moment My max. [Nm]
Maximum torque (Mz max. [Nm])
Max. force axial Fz max. [N]
The full gripping force according to the data table may only be achieved after several hundred gripping cycles
Dimensions and maximum loads
The specified moments and forces are static values
apply per base jaw
and may occur simultaneously. These loads may occur in addition to the moment generated by the gripping force
General information about the model series
Gripping force
is the arithmetic sum of the individual forces acting on each jaw
at a distance P (see drawing)
finger length
The distance P is measured from the same reference surface in the direction of the main axis. The maximum permissible finger length applies up to the nominal operating pressure. At higher pressures
the finger length must be reduced proportionally to the nominal operating pressure
Repeatability
is defined as the dispersion of the final position over 100 consecutive strokes
workpiece weight
This is calculated for frictional engagement with a coefficient of static friction of 0.1 and a safety factor of 2 against slippage of the workpiece under gravitational acceleration g. Significantly higher permissible workpiece weights result from positive engagement
Closing and opening times
These are pure movement times of the basic jaws without application-specific gripper fingers. Valve switching times
hose filling times
or PLC response times are not included and must be taken into account when determining cycle times
Operating principle
Wedge gear with surface power transmission
Housing material
aluminum
Basic baking material
Steel
activity